王鏡然 王英杰 莊宏偉 紀民尊 劉文鳳
低壓電纜絕緣熱氧老化過程中介電響應的Davidson-Cole分析
王鏡然1王英杰2莊宏偉3紀民尊1劉文鳳1
(1. 電力設備電氣絕緣國家重點實驗室(西安交通大學) 西安 710049 2. 蘇州熱工研究院有限公司 蘇州 215004 3. 廣西防城港核電有限公司 防城港 538001)
基于Davidson-Cole模型提取極化響應的弛豫強度、弛豫時間及電導損耗等特征量,分析熱氧老化過程中核級低壓電纜絕緣各特征量的變化規律,闡明老化過程中微觀與宏觀性能下降的一致性。首先在165℃下對試樣進行人工加速老化實驗,獲得不同劣化程度的試樣,測試老化過程中試樣理化特性、力學特性與介電響應的變化規律,發現老化過程中試樣發生再交聯反應,老化后期氧化反應加速進行;然后利用Davidson-Cole介電模型提取弛豫與電導特征參數,發現分子鏈段運動弛豫強度Δα、熱離子弛豫強度Δδ與直流電導率dc隨老化時間增加呈逐漸下降趨勢,老化504 h后,氧化反應的加速進行減緩了Δα與dc的下降,再交聯反應對特征參數的變化起主導作用;最后對介電模型特征參數Δα、Δδ、dc與斷裂伸長率進行初步擬合,結果顯示Δα、Δδ和dc與斷裂伸長率呈正相關,可見頻域介電譜的定量分析可應用于低壓電纜老化狀態評估。
低壓電纜 熱氧老化 介電響應 Davidson-Cole模型
低壓電纜廣泛應用于核電站中電力的傳輸、數據與信號通信、儀器儀表的控制等方面[1-3]。電纜在運行過程中會受到溫度、輻射、機械應力等多種因素的影響,隨著服役時間的增加,電纜材料逐漸劣化,嚴重時會引發危害電纜運行的安全問題。對于運行在核反應堆安全殼以外的電纜,熱與氧的作用是其老化的主要因素,因此有必要深入探究低壓電纜的熱氧老化機制與劣化規律[4-5]。
傳統用于評估低壓電纜絕緣狀態的最常見的標準是力學參量,主要是斷裂伸長率(Elongation at Break, EAB),然而拉伸實驗是破壞性的局部測量,不能反映電纜的整體絕緣狀態[6]。近年來,頻域介電譜法作為新型無損診斷技術,具有非破壞性、操作簡單等優點,適宜電纜的整體絕緣狀態表征。國內外學者開展了大量的研究工作,探索溫度、輻射等因素對電纜頻域介電譜特性的影響[7-16]。這些研究重點著眼于定性地分析頻域介電譜隨各種影響因素的變化規律,因此,尋找一種合理的介電物理模型擬合低壓電纜的復介電常數曲線,提取特征參量,是實現頻域介電譜特性定量分析的有效手段。
介電響應特征作為聚合物材料的關鍵性能指標,與電介質材料極化與電導損耗有關,受熱氧老化對分子鏈段運動弛豫極化、熱離子弛豫極化、直流電導等性能有顯著影響。K. S. Cole和R. H. Cole在經典Debye弛豫模型基礎上提出了著名的Cole-Cole模型,并使模型適用性拓展至更多電介質材料[17]。楊麗君等采用修正Cole-Cole模型分析了不同溫度及水分含量對油紙絕緣介電模型參數的影響[18-19]。劉驥等給出了老化評估中油紙絕緣Davidson-Cole模型參數的提取方法,進一步驗證了介電模型在絕緣狀態定量分析上的應用[20]。閔道敏等針對核級電纜開展老化研究,發現核電纜存在兩個弛豫過程,并采用Cole-Cole模型獲得了熱膨脹系數、介電弛豫強度等特征參數與輻照劑量的關系[21-22]。目前,將Davidson-Cole介電模型應用在低壓電纜熱氧老化過程中頻域介電譜的參數變化規律的研究鮮有報道,因此,采取科學的介電模型分析低壓電纜介電響應特性,同時分析介電響應特征參數與材料老化狀態的相關性,具有重要的工程意義與研究價值。
由于核電纜的特殊使用環境,電纜絕緣要求具有低煙無鹵阻燃功能。阻燃交聯聚烯烴作為我國第三代核電纜研發的重要絕緣材料,其阻燃劑成分占比較高(約占60%),阻燃交聯聚乙烯(Polyethylene, PE)/乙烯-醋酸乙烯酯共聚物(Ethylene-Vinyl Acetate copolymer, EVA)可以顯著地提升聚合物的力學性能與填料的承載能力,受到了各國學者的廣泛關注[4,23-25]。本文針對輻照交聯PE與EVA共混物開展熱氧老化實驗,測試了試樣在不同老化時間下的理化特性和力學特性,基于Davidson-Cole模型分析電纜不同老化時間下介電響應特性,提取介電弛豫強度、直流電導率等特征參數,探究不同老化時間下理化特性、力學特性與阻燃交聯聚烯烴材料介電響應特征的影響規律和機制,為低壓電纜老化研究提供實驗和理論依據。
聚合物的結構復雜,分子量的分散性及相鄰鏈間的協同作用使其具有更寬的弛豫時間分布,在適用于單一弛豫時間的線性介質的Debye弛豫模型基礎上,通過引入弛豫形狀參數,得到電介質Cole-Cole弛豫模型[17]為
式中,為角頻率;s為試樣靜態介電常數;hf為試樣高頻介電常數;為弛豫時間常數;弛豫形狀參數滿足0<≤1。
Davidson和R. H. Cole通過實驗觀察,在Cole-Cole模型基礎上發現部分聚合物符合另一種弛豫時間分布,引入弛豫形狀參數(0<≤1),提出了Davidson-Cole模型[26],即
式中,Δδ、δ、δ分別為弛豫過程的介電弛豫強度、介電弛豫時間常數及形狀參數;Δα、α、α分別為弛豫過程的介電弛豫強度、介電弛豫時間常數及形狀參數;0為真空下的介電常數,0=8.854× 10-12F/m;dc為試樣的直流電導率[27-29]。
試樣為國內某核電公司按照試運行低壓電纜(K3級)配方1:1代加工制得,其中主要成分為PE與EVA(質量比為PE:EVA=7:10)、助交聯劑、抗氧劑、低煙無鹵阻燃劑等,經平板熱壓法制得厚度約為1 mm的試樣,最后進行輻照交聯處理,劑量為100 kGy(1 Gy=1 J/kg)。根據標準IEC 60216-1:2013與GB/T 11026.1—2016對樣品在165 ℃溫度下進行人工加速老化實驗,在老化時間為0、48、168、336、504、672、840 h取出樣品用于后續實驗分析[4]。
2.2.1 紅外光譜實驗
采用日本SHIMADZU生產的IR Prestige-21型紅外光譜儀分析老化過程對試樣化學結構的影響。采用衰減全反射(Attenuated Total Reflection, ATR)模式,掃描范圍為4 000~500 cm-1,分辨率為4 cm-1,掃描次數為32。
2.2.2 凝膠含量實驗
采用萃取法測試試樣老化過程中大分子網絡的變化。首先稱重(0.3±0.01) g試樣,將120目不銹鋼網制成方形口袋狀;然后將試樣裝入不銹鋼網中,制成方形網包;最后將網包放入盛有二甲苯的圓底燒瓶中,冷凝回流萃取24 h。萃取結束后將網包放入80 ℃真空烘箱中干燥48 h至恒重。考慮到復合試樣中無機填料在萃取前后質量基本不變[30],本文對PE與EVA的凝膠含量進行測試,表達式為
式中,1為不銹鋼網質量;2為網包質量;3為干燥后網包質量;c為試樣中PE與EVA的質量分數。每種試樣進行兩次測試,取凝膠含量平均值作為最終結果。
2.2.3 寬頻介電譜實驗
采用德國Novcontrol 公司生產的Concept 80寬頻介電譜系統分析老化過程對試樣介電性能的影響。首先在試樣表面濺射直徑分別為30 mm、40 mm的圓形金電極,然后將試樣放置在烘箱內在50℃的條件下進行預處理12 h,用于去除試樣附著的水分。測試電壓為1 V,測試溫度為100℃,測試頻率為10-1~106Hz。
2.2.4 拉伸實驗
采用美斯特工業系統的5kNCMT—4503萬能電子拉力機對試樣進行拉伸測試,根據標準IEC IEEE 62582—3—2012,將試樣加工成啞鈴形樣條,拉伸速率設置為20 mm/min,每種試樣進行5次測試,取斷裂伸長率的平均值作為該試樣的最終結果。
3.1.1 傅里葉紅外光譜
熱氧作用會引起聚合物材料的化學結構變化,不同老化時間下試樣的紅外光譜如圖1所示。其中,2 919 cm-1和2 849 cm-1為亞甲基(—CH2)伸縮振動峰、1 463 cm-1為亞甲基變角振動峰。EVA中存在典型的1 736 cm-1酯基吸收振動峰,1 700~1 750 cm-1羰基峰為本征基團與老化產物的疊加。試樣在老化672 h、840 h時振動峰顯著減小,這是由于ATR模式會受到試樣表面硬度的影響,吸收峰減弱[31-32]。為了定量探究試樣熱氧老化過程中羰基的變化規律,本文將1 700~1 750 cm-1與1 463 cm-1峰面積(見圖1中虛線框部分)之比定義為羰基指數,用以觀察EVA中乙酸乙烯酯基團的降解及試樣的氧化程度[2,6],每種試樣進行3次紅外光譜測試,取羰基指數的平均值作為最終結果。
熱氧老化過程中試樣的羰基指數變化規律如圖2所示,發現在老化504 h以前,試樣的羰基指數逐漸減小,其中老化168 h以前羰基指數減小得最快,這主要是由熱作用下EVA中乙酸乙烯酯熱裂解導致。在老化進行至504 h以后,可以看到羰基指數增加,同時圖1中波長1 700~1 750 cm-1范圍內峰寬顯著變大,在老化后期試樣熱降解過程中氧化反應加速進行,生成酮、醛、酯、羧酸等羰基,使吸收峰變寬,羰基指數增加[4,31,33]。
圖1 不同老化時間下試樣紅外光譜
圖2 不同老化時間下試樣的羰基指數
3.1.2 交聯度
熱氧作用下試樣的交聯度可能會發生相應的變化,采用凝膠含量反映老化過程中試樣的交聯結構完整度。熱氧老化過程中試樣的凝膠含量變化規律如圖3所示,可見隨著老化時間的延長,試樣的凝膠含量逐漸增加,經歷840 h老化后,試樣凝膠含量由初始時的53.3%增長至79.9%。分析可知,試樣老化過程中因分子鏈斷裂產生的自由基在相互作用下彼此連接,形成新的交聯鍵,即發生了再交聯反應,使試樣中三維立體網狀結構增加。交聯度的增加使試樣宏觀表現變硬,這也是圖1中試樣在ATR模式下老化后期峰強度明顯減小的主要原因[32,34]。
圖3 不同老化時間下試樣凝膠含量
3.2.1 基于Davidson-Cole模型的介電譜分析
圖4 不同老化時間下試樣復介電常數頻譜
基于以上的分析,試樣在較高溫度時存在兩個弛豫過程與,同時考慮直流電導率dc的影響,本文采用Davidson-Cole介電弛豫模型來表示試樣在不同老化時間下的復介電常數?,如式(3)所示。通過Matlab編程,采用最小二乘法對試樣的介電頻域譜進行擬合,得到試樣復介電常數的實虛部擬合曲線[18-20]。
熱氧老化48 h時,試樣復介電常數實部(相對介電常數)與虛部(介質損耗)的實驗及擬合結果對比如圖5所示,可以看出試樣的擬合程度較好,其中形狀參數δ與α分別為0.59±0.005和0.3±0.005。從圖5a中可以看出,弛豫過程及試樣高頻相對介電常數hf對相對介電常數貢獻較大;從圖5b中看出,直流電導率dc及弛豫過程在介質損耗中低頻區占主導作用,而在高頻區弛豫過程的貢獻較大。下面針對Davidson-Cole介電模型中特征參數Δα、Δδ、dc與老化時間的關聯性進行討論。
圖5 試樣老化48 h復介電常數實驗與擬合結果對比
3.2.2 分子鏈段運動弛豫分量
試樣分子鏈段運動弛豫強度?α隨老化時間的變化規律如圖6所示,可見Δα隨老化時間的延長逐漸下降,其中Δα在老化初期下降較為明顯,在老化進行168 h時已下降至初始值的61.1%。在熱氧條件下的分子鏈段運動弛豫強度變化可以用自由體積理論來解釋[26]。聚合物自由體積在廣義上為無定形區未被分子鏈占據的部分體積。在熱氧老化初始階段,試樣發生再交聯反應,自由體積減少,限制了分子鏈段運動,使分子鏈段運動弛豫強度Δα在老化初期降低[21,26]。老化中期試樣的分子鏈段弛豫強度略降低,是由于抗氧劑的作用抑制了試樣的熱氧老化過程,使老化進行緩慢。在504 h以后,交聯反應與氧化反應二者相互競爭,熱氧降解導致的分子鏈斷裂及氧化產物生成使Δα相較于老化初期下降減緩。在整個老化過程中,交聯在分子鏈段運動的強度變化上占主導地位。
圖6 試樣不同老化時間下弛豫強度Δεα
試樣中不同尺寸的分子鏈段有著不同的弛豫時間常數,從而形成了一個較寬的弛豫時間分布。進一步探究分子鏈段運動弛豫時間分布特性,Davidson-Cole介電模型的弛豫時間分布關系式為
式中,α()為弛豫過程的弛豫時間分布函數;為弛豫過程的弛豫時間。本文中將弛豫時間大于弛豫時間常數α部分的函數值計為0[28]。
分子鏈段運動弛豫過程的弛豫時間分布如圖7所示,可以看出,隨著老化的進行,弛豫時間逐漸增加,對應著損耗峰向低頻處偏移。這種變化趨勢與試樣交聯程度緊密相關,自由體積的減小限制了分子鏈段的運動,弛豫時間在老化過程中逐漸增加。相較于弛豫強度α,弛豫時間分布α()在老化過程中總體變化程度較小。
3.2.3 熱離子弛豫極化及直流電導分量
介電弛豫強度Δδ隨熱氧老化時間的變化如圖8所示。從圖8可以看出,介電弛豫強度Δδ在老化過程中呈逐漸下降的趨勢,在老化進行至840 h時,Δδ已下降為初始值的49.1%。試樣中存在的離子主要源于填料中的雜質,離子受熱越過束縛勢壘形成宏觀偶極矩,在交變電場下形成熱離子弛豫極化[35]。隨著老化的不斷進行,試樣交聯度增加,大分子網狀結構的增加使離子躍遷受阻,熱離子弛豫強度下降。
圖7 試樣不同老化時間下弛豫時間分布
圖8 試樣不同老化時間下弛豫強度Δεδ
試樣直流電導率dc隨熱氧老化時間的變化如圖9所示。可以看出,直流電導率dc在老化過程中逐漸減小,在504 h前dc下降較快,504 h后下降趨勢逐漸減緩。高聚物中的電導包括離子電導與電子電導,其中,低電場高溫下主要是離子電導[26]。同時本文中試樣是阻燃交聯聚烯烴,因此試樣的電導主要來源于雜質離子[36]。隨著熱氧老化的不斷進行,試樣的分子間交聯鍵增多,分子間相互作用增加,顯著抑制了離子的定向遷移,試樣的電導率降低。在504 h后,氧化反應不斷進行,氧化產物的增加使載流子濃度有所提升,而交聯度進一步提升,抑制了載流子的遷移,二者競爭機制下dc相較于老化初期下降趨勢減緩。在整個老化過程中,交聯度作為關鍵因素,對試樣載流子遷移變化起主導作用。
圖9 試樣不同老化時間下直流電導率σdc
斷裂伸長率作為核電站電纜絕緣壽命的傳統標準,對熱氧老化具有優異的敏感度。圖10給出了不同老化時間下試樣斷裂伸長率隨老化時間的變化規律。從圖10可以看出,配方電纜試樣初始斷裂伸長率為185.16%,試樣的斷裂伸長率在老化504 h以前總體呈小幅下降趨勢,在老化504 h以后,試樣斷裂伸長率快速下降,材料力學性能被嚴重破壞。核級電纜的特殊性使試樣中添加了大量的阻燃劑,盡管試樣初始力學性能相比交聯聚乙烯(Cross Linked Polyethylene, XLPE)、交聯EVA有所下降,但仍保持了較好的抗撕裂性[23]。高聚物材料的斷裂伸長率主要取決于材料中的大分子柔性,在老化504 h以前,試樣發生再交聯反應,交聯度的提升引起試樣大分子網絡結構增加,材料柔性降低,阻礙了分子鏈段運動導致難以實現高彈形變,此時試樣變脆,斷裂伸長率下降[8,15,26]。在老化504 h以后,從圖2可知氧化反應加速進行,氧化產物逐漸增多,同時交聯度的進一步提升均使試樣大分子柔性降低,斷裂伸長率急劇下降。根據國際原子能機構(Inter- national Atomic Energy Agency, IAEA)的建議,通常采用試樣的斷裂伸長率下降為初始值的50%時作為該試樣的機械標準失效時間,即試樣在672 h時可判定為失效[37-38]。
圖10 不同老化時間下試樣斷裂伸長率
介電模型特征參數隨老化時間的單調變化如圖6、圖8、圖9所示,進一步探究特征參數與傳統狀態評估標準的相關性,圖11給出了斷裂伸長率與Δα、Δδ、dc的初步擬合結果。從圖11可以看出,弛豫強度Δα、Δδ和直流電導率dc與斷裂伸長率呈現較好的正相關性。凝膠含量作為關鍵參數,在老化過程中逐漸增加,試樣交聯度的提升抑制了離子的遷移,試樣自由體積減小,大分子柔性降低,顯著改變了試樣的介電特性與力學特性,使介電特征參數與力學參數具有一致性。通過建立二者的聯系,表明Davidson-Cole介電模型可以成為低壓電纜熱氧老化機制及狀態評估的有利工具。
圖11 試樣斷裂伸長率與特征參數相關性
本文采用紅外光譜、凝膠含量實驗、拉伸實驗、頻域介電譜研究了低壓電纜熱氧老化過程中的理化特性、力學特性與介電響應特性的變化規律及關聯性,得到的主要結論如下:
1)試樣在老化前期羰基指數的減小源于乙酸乙烯酯的降解,504 h后熱氧反應加速進行,羰基指數增加,同時試樣在老化過程中發生再交聯反應。
2)老化過程中試樣的再交聯反應對介電模型特征參數的變化起主導作用,分子鏈段運動弛豫強度Δα、熱離子弛豫強度Δδ與直流電導率dc隨著老化時間的增加逐漸下降。其中,504 h后分子鏈的氧化反應加速進行,使Δα與dc下降趨勢減緩。
3)隨著老化時間延長,試樣斷裂伸長率下降顯著,在672 h時判定失效,初步驗證了Davidson-Cole介電模型特征參數與斷裂伸長率具有良好的相關性。
本文揭示了不同老化程度下介電響應特征參數的定量變化規律及其與理化特性、力學特性的聯系,發現頻域介電譜的定量分析不僅可以表征材料的介電響應機理,而且與斷裂伸長率具有強關聯性,在低壓電纜狀態與壽命評估應用方向具有廣闊的發展前景。
[1] Powers W F. The basics of power cable[J]. IEEE Transactions on Industry Applications, 1994, 30(3): 506-509.
[2] Suraci S V, Fabiani D, Xu A, et al. Ageing assessment of XLPE LV cables for nuclear applications through physico-chemical and electrical measurements[J]. IEEE Access, 2020, 8: 27086-27096.
[3] 周濤, 秦雪猛, 李子超, 等. 核電纜發展分析研究[J]. 黑龍江電力, 2018, 40(4): 283-286. Zhou Tao, Qin Xuemeng, Li Zichao, et al. Analysis and research of nuclear cable development[J]. Heilongjiang Electric Power, 2018, 40(4): 283-286.
[4] Chi Xiaohong, Li Jianxi, Ji Minzun, et al. Thermal-oxidative aging effects on the dielectric properties of nuclear cable insulation[J]. Materials, 2020, 13(10): 2215.
[5] 曹丹, 孫彬, 單永東, 等. 核電用交聯三元乙丙絕緣材料熱氧老化狀態的評估[J]. 合成材料老化與應用, 2019, 48(3): 1-5, 63. Cao Dan, Sun Bin, Shan Yongdong, et al. Evaluation of thermal oxygen aging status of crosslinked EPDM insulation materials for nuclear power[J]. Synthetic Materials Aging and Application, 2019, 48(3): 1-5, 63.
[6] Suraci S V, Fabiani D, Roland S, et al. Multi scale aging assessment of low-voltage cables subjected to radio-chemical aging: towards an electrical diagnostic technique[J]. Polymer Testing, 2021, 103: 107352.
[7] 杜伯學, 韓晨磊, 李進, 等. 高壓直流電纜聚乙烯絕緣材料研究現狀[J]. 電工技術學報, 2019, 34(1): 179-191. Du Boxue, Han Chenlei, Li Jin, et al. Research status of polyethylene insulation for high voltage direct current cables[J]. Transactions of China Electro-technical Society, 2019, 34(1):179-191.
[8] 周凱, 李詩雨, 尹游, 等. 退運中壓XLPE和EPR電纜老化特性分析[J]. 電工技術學報, 2020, 35(24): 5197-5206. Zhou Kai, Li Shiyu, Yin You, et al. Analysis of aging characteristics of medium voltage XLPE and EPR retired cables[J]. Transactions of China Electro-technical Society, 2020, 35(24): 5197-5206.
[9] Glass S W, Fifield L S, Dib G, et al. State of the art assessment of NDE techniques for aging cable management in nuclear power plants FY2015[R]. Pacific Northwest National Lab, Richland, WA, USA, 2015.
[10] Linde E, Verardi L, Fabiani D, et al. Dielectric spectroscopy as a condition monitoring technique for cable insulation based on crosslinked polyethylene[J]. Polymer Testing, 2015, 44: 135-142.
[11] 劉剛, 劉斯亮, 金尚兒, 等. 基于理、化、電特性的110 kV XLPE絕緣電纜剩余壽命的綜合評估[J]. 電工技術學報, 2016, 31(12): 72-79, 107. Liu Gang, Liu Siliang, Jin Shanger, et al. Comprehensive evaluation of remaining life of 110 kV XLPE insulated cable based on physical, chemical and electrical properties[J]. Transactions of China Electrotechnical Society, 2016, 31(12): 72-79, 107.
[12] 張益舟, 龔智明, 王雷, 等. 基于介電性能的電纜熱老化及輻照老化檢測技術研究[J]. 絕緣材料, 2017, 50(9): 62-67. Zhang Yizhou, Gong Zhiming, Wang Lei, et al. Thermal and irradiation ageing detection technology of cables based on dielectric properties[J]. Insulating Materials, 2017, 50(9): 62-67.
[13] 單秉亮, 李舒寧, 楊霄, 等. XLPE配電電纜缺陷診斷與定位技術面臨的關鍵問題[J]. 電工技術學報, 2021, 36(22): 4809-4819. Shan Bingliang, Li Shuning, Yang Xiao, et al. Key problems faced by defect diagnosis and location technologies for XLPE distribution cables[J]. Transactions of China Electrotechnical Society, 2021, 36(22): 4809-4819.
[14] 王昊月, 李成榕, 王偉, 等. 高壓頻域介電譜診斷XLPE電纜局部絕緣老化缺陷的研究[J]. 電工技術學報, 2022, 37(6): 1542-1553. Wang Haoyue, Li Chengrong, Wang Wei, et al. Local aging diagnosis of XLPE cables using high voltage frequency domain dielectric spectroscopy[J]. Transactions of China Electrotechnical Society, 2022, 37(6): 1542-1553.
[15] 劉濤, 李歡, 徐磊, 等. 熱老化對XLPE微觀結構及介電性能的影響機制綜述[J]. 陜西理工大學學報(自然科學版), 2021, 37(4): 1-9, 31. Liu Tao, Li Huan, Xu Lei, et al. Review of effects of thermal aging on micro-structure and performance of cross-linked polyethylene cable insulation[J]. Journal of Shaanxi University of Technology (Natural Science Edition), 2021, 37(4): 1-9, 31.
[16] Zhou Haolong, Hanafusa W, Udo K, et al. Aging behavior of flame-retardant cross-linked polyolefin under thermal and radiation stresses[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2021, 28(1): 303-309.
[17] Cole R H. Dielectric polarization and relaxation[M]// Molecular Liquids. Dordrecht: Springer Netherlands, 1984: 59-110.
[18] 楊麗君, 齊超亮, 鄧幫飛, 等. 采用修正Cole-Cole模型提取油紙絕緣頻域介電譜的特征參量方法[J]. 高電壓技術, 2013, 39(2): 310-317. Yang Lijun, Qi Chaoliang, Deng Bangfei, et al. Application of modified Cole-Cole model to extract characteristics of frequency dielectric spectroscopy of oil-paper insulation[J]. High Voltage Engineering, 2013, 39(2): 310-317.
[19] 楊麗君, 高思航, 高竣, 等. 油紙絕緣頻域介電譜的修正Cole-Cole模型特征參量提取及水分含量評估方法[J]. 電工技術學報, 2016, 31(10): 26-33. Yang Lijun, Gao Sihang, Gao Jun, et al. Characteristic parameters extracted from modified Cole-Cole model and moisture content assessment methods study on frequency-domain dielectric spectroscopy of oil-paper insulation[J]. Transactions of China Electrotechnical Society, 2016, 31(10): 26-33.
[20] 劉驥, 尹夢涵, 李秀婧, 等. 油紙絕緣老化評估的Davidson-Cole模型參數提取方法[J]. 電機與控制學報, 2017, 21(3): 63-70. Liu Ji, Yin Menghan, Li Xiujing, et al. Parameters extraction of Davidson-Cole model on aging assessment of oil-paper insulation[J]. Electric Machines and Control, 2017, 21(3): 63-70.
[21] Min Daomin, Li Shengtao, Hirai N, et al. Dielectric spectroscopic analysis of degradation in ethylene-propylene-diene copolymer[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2016, 23(6): 3620-3630.
[22] Min Daomin, Yan Chenyu, Huang Yin, et al. Dielectric and carrier transport properties of silicone rubber degraded by gamma irradiation[J]. Polymers, 2017, 9(10): 533.
[23] 馬以正, 侯海林. 輻射交聯無鹵阻燃聚烯烴復合材料的研究[J]. 核技術, 1997, 20(7): 408-412. Ma Yizheng, Hou Hailin. Preparation of non-halogen flame retardant polyolefin complex by radiation crosslinking[J]. Nuclear Techniques, 1997, 20(7): 408-412.
[24] 丁圓, 張宏, 劉琪, 等. PE/EVA共混改性研究進展[J]. 化工時刊, 2020, 34(10): 22-24, 59. Ding Yuan, Zhang Hong, Liu Qi, et al. Research progress of PE/EVA blending modification[J]. Chemical Industry Times, 2020, 34(10): 22-24, 59.
[25] Colombani J, Sidi A, Larché J F, et al. Thermooxidative degradation of crosslinked EVA/EPDM copolymers: impact of Aluminium TriHydrate (ATH) filler incorporation[J]. Polymer Degradation and Stability, 2018, 153: 130-144.
[26] 雷清泉. 高聚物的結構與電性能[M]. 武漢: 華中理工大學出版社, 1990.
[27] 林生軍, 黃印, 謝東日, 等. 環氧樹脂高溫分子鏈松弛與玻璃化轉變特性[J]. 物理學報, 2016, 65(7): 304-310. Lin Shengjun, Huang Yin, Xie Dongri, et al. Molecular relaxation and glass transition properties of epoxy resin at high temperature[J]. Acta Physica Sinica, 2016, 65(7): 304-310.
[28] 康文斌, 蒙紹興, 李世軍, 等. 硅橡膠絕緣介質的分子鏈運動與電極極化特性[J]. 高電壓技術, 2018, 44(12): 3798-3807. Kang Wenbin, Meng Shaoxing, Li Shijun, et al. Molecular chain motion and electrode polarization properties of silicone rubber[J]. High Voltage Engineering, 2018, 44(12): 3798-3807.
[29] Ohki Y. Broadband complex permittivity and electric modulus spectra for dielectric materials research[J]. IEEJ Transactions on Electrical and Electronic Engineering, 2022, 17(7): 958-972.
[30] Sidi A, Colombani J, Larché J F, et al. Multiscale analysis of the radiooxidative degradation of EVA/EPDM composites. ATH filler and dose rate effect[J]. Radiation Physics and Chemistry, 2018, 142: 14-22.
[31] 翁詩甫. 傅里葉變換紅外光譜分析[M]. 2版. 北京: 化學工業出版社, 2010.
[32] Yamaguchi H, Ishii H, Hirai N, et al. Degradation of mechanical and dielectric properties of flame-retardant ethylene propylene rubber by thermal aging[J]. IEEJ Transactions on Electrical and Electronic Engineering, 2020, 15(4): 488-495.
[33] Allen N S, Edge M, Rodriguez M, et al. Aspects of the thermal oxidation of ethylene vinyl acetate copolymer[J]. Polymer Degradation and Stability, 2000, 68(3): 363-371.
[34] 何平笙. 新編高聚物的結構與性能[M]. 北京: 科學出版社, 2009.
[35] 朱誠身. 聚合物結構分析[M]. 北京: 科學出版社, 2004.
[36] 秦書娟, 徐曼, 曹曉瓏, 等. EVA/VLDPE/Mg(OH)2阻燃體系介電性能研究[J]. 電線電纜, 2010(3): 31-34, 37. Qin Shujuan, Xu Man, Cao Xiaolong, et al. Study on the dielectric performance of EVA/VLDPE/Mg(OH)2composite[J]. Electric Wire & Cable, 2010(3): 31-34, 37.
[37] International Atomic Energy Agency. Assessment and management of ageing of major nuclear power plant components important to safety: volume Ⅱin-containment instrumentation and control cables[M]. Vienna: International Atomic Energy Agency, 2000.
[38] Fabiani D, Suraci S V. Broadband dielectric spectroscopy: a viable technique for aging assessment of low-voltage cable insulation used in nuclear power plants[J]. Polymers, 2021, 13(4): 494.
Dielectric Response During Thermal-Oxidative Aging of Low-Voltage Cable Insulation Analyzed by Davidson-Cole
Wang Jingran1Wang Yingjie2Zhuang Hongwei3Ji Minzun1Liu Wenfeng1
(1. State Key Laboratory of Electrical Insulation and Power Equipment Xi’an Jiaotong University Xi’an 710049 China 2. Suzhou Nuclear Power Research Institute Suzhou 215004 China 3. Guangxi Fangchenggang Nuclear Power Co. Ltd Fangchenggang 538001 China)
The low-voltage(LV) cables in nuclear power plants would be affected by heat and oxygen under actual operation, and the cable materials would gradually deteriorate with the increase of service time. The most common standard traditionally used to evaluate the insulation state of LV cables was the mechanical parameter, mainly elongation at break (EAB), however, the tensile experiments were destructive. Rencently, frequency domain spectroscopy (FDS), as one new non-destructive diagnostic technology, had the advantages of being non-destructive and simple, and was suitable for the characterization of the overall insulation state of the cables. However, the vast majority of studies focused on qualitatively analyzing the variation of the FDS with various influencing factors. Therefore, one scientific dielectric model was used to quantitatively analyze the dielectric response characteristics of LV cables, and the correlation between the dielectric parameters and the physical, chemical, mechanical properties of the materials was discussed.
Firstly, the accelerated aging experiments were carried out on the cross-linked polyethylene (PE)/ ethylene-vinyl acetate copolymer (EVA) specimens at 165℃ to obtain the samples with different degrees of deterioration. The changes in physical and chemical properties of PE/EVA specimens were tested through the Fourier transform infrared (FTIR) spectroscopy and the gel content. The deterioration of the mechanical property was investigated through the EAB experiment, and the dielectric properties were analyzed through the FDS at 100℃. The PE/EVA specimens had two relaxation processes form the analysis of FDS, and the DC conductance was considered at the same time. Therefore, the complex permittivity spectra of the PE/EVA samples with different aging degrees were fitted by the Davison-Cole dielectric model to extract the characteristic parameters of polarization and conductance.
The results showed that the re-crosslinking reaction of the specimens occurs during the whole aging process, which increased the three-dimensional network structure. The carbonyl index of PE/EVA showed a trend of decreasing at the beginning and then increasing, which was caused by the degradation of vinyl acetate groups at the early stage and the oxidation reaction after 504 h. It was found that the relaxation strength Δαdue to the motion of segmental chains, the thermionic polarization strength Δδas well as the DC conductivitydcgradually decreased with the increase of aging time through the Davidson-Cole dielectric model. The decrease of Δαanddcslowed down due to the accelerated oxidation reaction after 504 h. The preliminary fitting of the characteristic parameters Δα, Δδ,dcof the dielectric model and the traditional state evaluation criteria EAB showed a positive correlation.
The following conclusions can be drawn from the analysis of experimental and fitting results: (1) The degree of cross-linking, as the key parameter during the aging process, is the most important determinant of the consistency between the dielectric parameters and the mechanical parameter. The increase in the degree of cross-linking of PE/EVA inhibits the migration of ions, so that the DC conductivitydcand the relaxation strength of the samples decrease with the aging time. The free volume of PE/EVA specimens is reduced due to the augment of the macromolecular network structure, which weakens the movement of the molecular segments. At the same time, the increase of the degree of cross-linking reduces the flexibility of macromolecules of PE/EVA, and then the EAB decreases during the aging process. (2) It is found that the quantitative analysis of the frequency domain spectroscopy can not only characterize the dielectric response mechanism of the materials, but also has a strong correlation with the elongation at break, which can be better applied in the evaluation of the state and life of the LV cables.
Low-voltage cables, thermal-oxidative aging, dielectric response characteristics, Davidson-Cole model
10.19595/j.cnki.1000-6753.tces.220882
TM215.92
陜西省重點研發計劃資助項目(2020ZDLGY09-10)。
2022-05-23
2022-07-06
王鏡然 男,1998年生,碩士研究生,研究方向為低壓電纜老化機理與狀態評估。E-mail:wangjingran1234@stu.xjtu.edu.cn
劉文鳳 女,1982年生,教授,博士生導師,研究方向為高分子電工材料,電力設備絕緣材料改性與評估。E-mail:liuwenfeng@xjtu.edu.cn(通信作者)
(編輯 李冰)