WAN Sheng， XIE Xiaoli

Sichuan Engineering Technical College， Deyang 618000， China

DesignandResearchontheLengthofPiston’sBufferOilMatAreaofaNewTypeofHydraulicRockDrill

WAN Sheng*， XIE Xiaoli

SichuanEngineeringTechnicalCollege，Deyang618000，China

Forthecomplicatedworkingconditionsofrockdrills,suchasacrackintherock,unevenhardnessofrockandimproperoperation,thepistonofrockdrillisunabletohitsteelchiseltailpromptly.Therefore,theemptyhittingphenomenonappears.Toavoidthisphenomenon,itisnecessarytodeducelengthofthepistonbufferoilmatarea.Accordingtoconstantdecelerationbufferstagemotionandvariabledecelerationbufferstagemotionofthepistonforanewhydraulicrockdrill，thepistondynamicsequationswerelistedseparatelyinthispaper.Furthermore,piston’smovingvelocityandaccelerationformulasarederivedduringitsemptyhittingbufferstage.Andthedesignandcalculationmethodofthelengthofpiston’sbufferoilmatareaisobtained.

newtypeofhydrauliccrockdrill，impactpiston，thelengthofpiston’soilmatarea

Percussive rock drill is important equipment in mining and quarrying. With the development of extractive industries, working behavior of hydraulic drill machine is in an increasingly high demand[1-4]. Compared with automatic reversing device of traditional hydraulic drill machine, the new type of hydraulic drill machine has two-position two-way hydraulic controlled reversing valve and two-position four-way hydraulic controlled reversing valve, which is connected with two-position two-way solenoid valve, pressure relief valve, pressure reducing valve, restrictive valve and check valve successively. The advantages of this kind of drill machine’s plunger tip are that the direction commutation is nimble, reliable, high frequency, quick reposition. And the plunger tip also can achieve self adaptive control under different operation conditions such as clay, rocks, sandstone. Besides, it has the features of high efficiency and low energy consumption. Based on the operating environment of the new hydraulic drill machine, the paper gives the length of piston’s buffer oil mat area, which is determined to avoid the empty hitting.

1.hydraulic pump，2.relief valve，3.impact mechanism， 4.hydraulic control one-way valve，5.pressure-reducing valve，6,10,12,15.throttle valve，7.two-position two-way solenoid valve，8,11.check valve, 9.two-position four-way hydraulic controlled reversing valve，13,14.two-position two-way hydraulic controlled reversing valve

Fig.1 Operating principle of the impact mechanism of a new hydraulic drill machine diagram

1.Operating principle of the impact mechanism of a new hydraulic drill machine

The two-position hydraulic controlled reversing valve, which is equipped in the plunger chip of new type hydraulic automatic reverse working device, come from patent ZL03134568.9. The operation principle of the patent will not be mentioned in this paper. Operation principle of the impact mechanism of the new hydraulic drill machine is shown in Fig.1. In the initial state, the impact pistonDis located at right side displacement by acting force ofHcavity gas spring. Pump 1 outlet in main oil system is connected with outletPof two-position four-way hydraulic controlled reversing valve 9, which is made of valve plug-to-outletAand piping-to-outletXto form straightway status. When pump 1 comes into operation, pressure oil flows from outletXto right cavityFof impact pistonD, at the same time, hydraulic control one-way valve opens and oil in left cavityCpasses through outletU, hydraulic control one-way valve 4, outletBandOof two-position four-way hydraulic controlled reversing valve 9, then reflows to tank. And then impact pistonDbegins moving to left until reaching left-most bit, thus outletWand cavityFare connected. Later on, pressure oil flows from check valve1 1, throttle valve 10, and enters into external-control outletKof hydraulic controlled reversing valve 9, and its main valve plug moves to right side and reverse to make its outletPand outletB, outletAand outletOwill be connected separately. And pressure oil flows from outletP, outletB, hydraulic control one-way valve 4 and outletUentering into cavityC, then passes by cavityF, outletX, outletAand outletOto reflow to oil return tank. And then impact pistonDaccelerates to right side by force of pressure oil and gas spring in cavityH. When it is accelerating to right side, due to difference of rock medium’s hardness, the piston will act in the two ways, one is the piston’s un-full-travel movement and rebound under the condition of crashing into hard rocks, the other is the piston’s full-travel movement and without rebound under the condition of crashing into soft clay and sandstones. The automatic movement process of spring back occurring midway is as follows. When hitting hard rock by plunger chipG, impact pistonDis bounced back before reaching the bottom of the cylinder liner. As a result, pressure in the left cavityCof impact pistonDrises to more than system setting pressure, which is transmitted from outletYto outletKof two-position two-way hydraulic controlled reversing valve 14. And its main valve plug moves to right side and reverses, and its outletPand outletOare connected to make the pressure of outer-controlled outletKof two-position four-way hydraulic controlled reversing valve 9 reach zero. The valve 9 has reset to left location, pressure oil goes through outlet P, outletAand outletXof valve 9, enters into cavityFof impact pistonD, flows through cavityC, outletU, hydraulic control one-way valve 4, outletBand outletOof valve 9, returns to oil return tank, finally impact pistonDmoves back to left side, and then the next loop begins.

The other kind of process of impact pistonD’s full-travel movement without rebound is listed below. When hitting soft by plunger chipG, impact pistonDmoves with full travel to its rightmost location, outletVis connected with cavityC, pressure oil flows from outletVto controll outletK″ of two-position two-way hydraulic controlled reversing valve 13, and its main valve plug moves to right side and reverses, and its outletPand outletOare connected to make the pressure of outer-controlled outletKof two-position four-way hydraulic controlled reversing valve 9 reach zero. The valve 9 has reset to left location, pressure oil goes through outletP, outletAand outletXof valve 9, enters into cavityFof impact pistonD, flows through cavityC, outletU, hydraulic control one-way valve 4, outletBand outletOof valve 9, returns to oil return tank, finally impact pistonDmoves back to left side, and then the next loop begins. On the oil passage of outer-controlled outletKof two-position four-way hydraulic controlled reversing valve 9, there is a reset-controlled two-position two-way solenoid valve 7. When this valve is energized, the pressure of outer-controlled outletKof two-position four-way hydraulic controlled reversing valve 9 is zero. Valve 9 has reset to left location, its outletPand outletAare connected, and impact pistonDmoves back to left side by main oil passage.

2.Design of the length of piston’s buffer oil mat area

The object of this paper is to design the piston’s buffer oil mat area length of a new type of hydraulic drill machine, and the equipment structure is shown in Fig. 2. When piston ought to hit but not hit the steel chisel tail, which is called piston’s empty hitting, two-position four-way hydraulic controlled reversing valve has completed stroke reversing, then high pressure oil enters into prior cavity in Fig. 2. Being moving with high speed, piston can’t be stopped by hydraulic pressure from moving promptly, but enters into buffer oil mat area at a specified maximum speed when hydraulic oil is surrounded inside buffer. During the process of buffering, acceleration of piston is various. According to the evolution of acceleration, the buffer is divided into two parts. In Fig. 2, system of rectangular coordinates is established to clear piston’s movement status. When -x1≤x<0, the piston locates in the first buffer area, that is uniform retarded motion buffering area. When x≥0, the piston locates in the second buffer area, that is variable decelerated motion buffering area.

Fig.2 Equipment structure diagram of designing of the piston’s buffer oil mat area length of a new type of hydraulic drill machine

2.1.Analysisofthefirstbufferarea

On the condition that piston ought to hit the steel chisel tail but not hit it, which is called piston’s empty hitting, two-position four-way hydraulic controlled reversing valve has completed stroke reversing. Then high pressure oil enters into front cavity as shown in Fig. 2, and behind cavity is connected with oil-return outlet. Now kinetic equation of impact piston is as follows:

(1)

In the equation,mis piston’s mass (kg) ，xis displacement (m)，tis piston’s motion time (s)，kis resistance coefficient，pis pressure of high-pressure oil (Pa)，p0is pressure of oil (Pa)，S1is compression area of piston’s front cavity (m2)，S2is compression area of piston’s behind cavity (m2).

The acceleration of the first buffer area can be deduced from Eq.(1) as follows:

(2)

Assuming the initial velocity of piston’s entering the first buffer area isvmax, which is maximum in the first buffer area. Then the piston’s velocity in the first buffer is obtained as follows:

v1=vmax+a1t

(3)

From the above analysis, we can see that the reciprocating motion of piston in the first buffer area isx1, and the piston’s total motion time in the first buffer area ist1, which could be obtained as follows:

(4)

Assembling formula (2)～ (4), the velocity of piston’s reaching origin of coordinates is:

(5)

2.2.Analysisofthesecondbufferarea

As is shown in Fig.3, after reaching origin of coordinates and entering the second buffer area, hydraulic oil in it is expelled from oil-drainage outlet. Because the motion velocity is still high, pressure of high-pressure oil in buffer area keeps rising. And the impact piston’s kinetic equation is:

(6)

In the equation,phis pressure of high-pressure oil in the second buffer area (Pa).

Fig.3 Structure diagram of the piston located in the second buffer area

If the influence of hydraulic oil’s condensibility and shear flow elided, according to hydromechanics theory, hydraulic oil’s leakage rate in the second buffer area is:

(7)

In the equation,dis diameter of piston’s shoulder (m)，d1is piston’s front-end diameter (m)，δis backlash between piston’s shoulder and cylinder body (m)，δ1is backlash between piston’s front end and front supporting sheath (m)，μis dynamic viscosity of hydraulic oil(Pa·s)，l1is oil sealing length between piston and front supporting sheath (m)，εis relative eccentricity between piston’s shoulder and inner cylinder body，ε1is relative eccentricity between piston’s front end and front supporting sheath hole.

When piston rushes forward, the flow rate of hydraulic oil from buffer cavity is:

(8)

3.Conclusions

This paper introduced the operation principle of a new type of hydraulic drill machine. On the basis of uniform retarded motion and variable decelerated motion, this paper analyzes the movement of piston in buffer oil pad area, and gives the calculating method of buffer oil pad area’s length. The calculation method, that this paper presented, has applied successfully in YYT30 hydraulic drilling machine. It is valuable both in theories and the applications to solve piston’s empty hitting phenomenon.

[1] Geof Perse.Hydraulic Rock Drills[J].Mining Magazine,1985(3): 220-231.

[2] Fiscor Steve.Underground miners test new hydraulic drill[J].Engineering and Mining Journal，2004,205(9):46-47．

[3] Placido Joao R.A New Type of Hydraulic Hammer Compatible with Conventional Drilling Fluids[C]//Proceedings SPE Annual Technical Conference and Exhibition,2003:2601-2607.

[4] Eliss D,Chiang L.Dynamic analysis of impact tools by using a method based on stress wave propagation and impulse-momentum principle[J].ASME Journal of Mechanical Engineering,2003,125:131-142.

新型液壓鑿巖機活塞緩沖油墊區長度設計

萬 圣*，謝曉利

四川工程職業技術學院，四川 德陽 618000

由于鑿巖工作環境比較復雜，如巖石中有裂縫、巖石軟硬不均以及操作不當?shù)龋沟描弾r機活塞不能及時撞擊到釬尾，從而出現空打現象。為了避免這種現象的發生，有必要確定活塞緩沖油墊區長度。根據新型液壓鑿巖機活塞等減速緩沖階段運動規律及活塞變減速緩沖階段運動規律，分別列出了活塞動力學方程表達式，進一步導出了活塞空打時緩沖期間的運動速度和加速度運算表達式，給出了活塞緩沖油墊區長度設計計算方法。

新型液壓鑿巖機；沖擊活塞；油墊區長度

TD421.2

2013-01-09

*WAN Sheng.E-mail:wanshengwww@163.com

10.3969/j.issn.1001-3881.2013.06.022