Li Li, Chen Ning, Liu Qing

(State Key Laboratory of Polymer Materials Engineering, Polymer Research Institute, Sichuan University, Chengdu 610065)

Drawing behavior of melt-spun poly(vinyl alcohol) fibers

Li Li, Chen Ning*, Liu Qing

(State Key Laboratory of Polymer Materials Engineering, Polymer Research Institute, Sichuan University, Chengdu 610065)

Poly(vinyl alcohol)(PVA) was plasticized by deionized water and was melt-spun into PVA fiber. The stress-strain curves of the melt-spun PVA fibers with 35% and 5% water by mass fraction at different drawing temperatures were measured as well as the activation energy. The results showed that the effect of drawing temperature on the apparent extensional viscosity of melt-spun PVA fibers containing 35% water by mass fraction could be divided into three zones: 30-100 ℃, 100-190 ℃ and 190-210 ℃, i.e. there were three different activation mechanisms and the fiber could be drawn at least through three steps; the stretching of the filaments was largely affected by the water content in the system; the motion ability of PVA molecular chains decreased and the apparent extensional viscosity of the melt-spun fibers increased with the reduction of the water content in system; the apparent extersional viscosity of the melt-spun PVA fiber with 5% water by mass fraction changed differently within two different temperature ranges, indicating two different activation mechanisms, so the as-spun fibers could be drawn through two steps.

poly(vinyl alcohol) fiber; melt-spinning; extensional viscosity; activation energy

Poly(vinyl alcohol) (PVA) fiber is widely used in many important high-tech areas owing to its excellent comprehensive properties, such as good mechanical properties, superior thermal properties and weather durability, excellent acid, alkaline and organic solvents resistance, etc. However, the melting point and decomposition temperature of PVA are so close that the melt spinning of PVA becomes very difficult due to the multi-hydroxyl structure. So far, PVA fiber has been produced by solution spinning[1], which is associated with low strength and modulus, high manufacturing cost caused by a large amount of energy consumption, long dissolving and drying time and recycle of coagulating bath.

Generally, the key point to realize the melt spinning of PVA is to obtain thermal processing window, i.e. decreasing the melting point of PVA and increasing its decomposition temperature, which can be performed by addition of plasticisers[2-3], chemical modification[4]and blending[5]. Among them, the plasticized melt spinning is simple, highly efficient and environmental friendly, which is the development direction of PVA melt spinning.

The author successfully realized the melt spinning of PVA according to the intermolecular complexation and plasticization.And the PVA as-spun fibers with uniform structure, circular cross-section and controllable diameter were obtained. Water, the key plasticizer for the melt spinning of PVA, exists in melt-spun PVA fibers in three different states[7], i.e., free water, freezable bound water and non-freezing water, which provides as-spun PVA fiber with good drawability at room temperature. However, excessive water would evaporate during the hot-drawing process of as-spun PVA fiber, resultting in the formation of internal defects. As a result, the drawability of PVA fibers was reduced. In this paper, the drawing behavior of melt-spun PVA fibers under different drawing temperature were studied; the apparent extensional viscosity as well as the activation energy were calculated, and the effect of water content on drawing behavior and drawing mechanism were analyzed, which provides theoretical basis for the preparation of PVA fibers at high draw ratio.

1 Experimental

1.1 Materials

PVA-1799F with an alcoholysis degree of 99.9% was commercially provided from Sichuan Vinylon Works,SINOPEC. The PVA raw materials were washed with deionized water until a pH value of 7 and dried at 80 ℃ to constant weight as the experimental sample in a vacuum oven.

1.2 Preparation of melt-spun PVA fibers

A modified PVA was obtained by adding pre-dried PVA into quantitative deionized water and then letting the solutions completely seep into PVA at 80 ℃ in a sealed vessel. Finally, the modified PVA was melt-spun in a melt spinning apparatus, which consisted of a single screw extruder with the diameter of 25 mm and length-diameter ratio of 25, a prefilter, a spin pump, spinnerets and a conventional take-up device. The capillary diameter of the spinnerets was 0.15 mm. The temperature of extruder and spin head was 120-150 ℃. The draw ratio was 1.5-2.0. The as-spun PVA fibers with 5% water by mass fraction were obtained by drying the melt-spun PVA fibers with 35% water by mass fraction at 200 ℃ for 3 min in an air-circulating oven.

1.3 Measurement of drawing behavior of melt-spun PVA fiber

The stress-strain curves of melt-spun PVA fibers were measured by a universal testing machine RGL-10(Shenzhen Reger Instrument Co., Ltd., China) at drawing temperature 30-220 ℃. The apparent extensional viscosity(ηε) was calculated by the following equations[8-9].

ηε=σε/ε

(1)

σε=F/At

(2)

ε=V/λtL0

(3)

Where,Atis cross-sectional area of PVA fiber at timet;Fis axial tensile force;Vis drawing speed;L0is initial length of melt-spun PVA fiber;λtis draw ratio at timet.

2 Results and discussion

2.1 Drawing behavior of melt-spun PVA fiber with 35% water by mass fraction

As shown in Fig.1, the drawability of melt-spun PVA fiber was sensitive to the drawing temperature. With the drawing temperature increasing, the hydrogen bonds interactions among PVA molecules were weakened, the motion ability of PVA molecule chain was enhanced, the tensile stress was decreased, and the stretch degree of PVA chains along the drawing direction and the elongation at break of the melt-spun PVA fiber were increased. However, the extremely high temperature made the water molecules move faster in melt-spun PVA fibers, which weakened the hydrogen bonds interaction between PVA and water. As a result, the water in melt-spun PVA fibers changed from bound water to free water and evaporated rapidly, causing internal defects to form in PVA fibers and the draw ratio to decrease. The transition temperature was 170-180 ℃.

Fig.1 Stress-strain curves of melt-spun PVA fibers with 35% water by mass fraction drawn at different temperature1—30 ℃；2—60 ℃；3—80 ℃；4—110 ℃；5—120 ℃；6—140 ℃；7—170 ℃；8—180 ℃；9—200 ℃；10—220 ℃

From Fig.2, it can be found thatηεkept rising with the draw ratio(λ) increasing, but the rise slowed down when the drawing temperature increased. The main reason is that the increase ofλmade PVA molecule chains orient, the molecular distance decrease, free water evaporate and the motion ability of PVA molecules weaken. Furthermore, the orientation of PVA molecule chains made hydrogen bond rebuilt and restricted the stretchability of PVA fibers. As a result,ηεof melt-spun PVA fibers increased with the increase ofλ.

Fig.2 Relationship between ηε and λ of melt-spun PVA fibers with 35% water by mass fraction drawn at different temperature■—80 ℃；●—100 ℃；▲—120 ℃；▼—140 ℃；◆—160 ℃；?—180 ℃；?—200 ℃；○—210 ℃

The high drawing temperature weakened the hydrogen bonds interactions among PVA molecules and promoted the movement of PVA chain, which improved the stretchability of melt-spun PVA fibers. Soηεdecreased with the increase of drawing temperature, which indicated that the drawing temperature played an important role in the drawing process of melt-spun PVA fiber and the tensile stress could be profoundly decreased by increasing temperature.

The relation betweenηεand drawing temperature (T) can be described by Eyring-Frenkel equation. From a graphic representation (Fig.3) of the experimental data of lnηεagainst 1/T, the extensional activation energy (Ea) can be determined by the slope of the linear plot. The values ofEaare listed in Tab.1. From Fig.3 and Tab.1, it can be seen thatηεof PVA fibers decreased with the increase of drawing temperature. The relationship between lnηεand 1/Texhibited three-segment straight line with inflection point temperature of 100 ℃ and 190 ℃. The correspondingEawas divided into three regions, i.e. 11.5-12.5 kJ/mol in the lower-temperature region of 30-100 ℃,12.9-24.7 kJ/mol in the middle-temperature region of 100-190 ℃, and 69.5-141.0 kJ/mol in the higher-temperature region of 190-210 ℃ .

Fig.3 Relationship between ηε and 1/T of melt-spun PVA fibers at different λ ■—4；●—5；▲—6；▼—7；◆—8；?—9；?—10

λEa/(kJ·mol-1)30-100℃100-190℃190-210℃411.512.969.5512.014.871.2612.317.881.1713.120.393.0812.521.1109.5919.8125.41024.7141.0

In lower-temperature region, the melt-spun PVA fibers contained more water,which offered the plasticization and lubrication effect in the fiber,and was not sensitive to temperature during the drawing process. So it can be speculated that there mainly happened the shrink of free volumes and distortion of amorphous region in PVA fiber, resulting in lowEa.

In middle-temperature region, free water totally evaporated.The freezable bound water and drawing temperature exerted synergistic effect on the drawability of PVA fibers, which made the large deformation of PVA fiber and the increase ofEa.

In higher-temperature region, freezable bound water evaporated completely. The deformation of melt-spun PVA fibers was mainly affected by drawing temperature. The chain-folded lamellae was melted in a certain extent. The drawing temperature was close to the melt point of PVA fibers. The structure of PVA fibers changed distinctly and became more sensitive to drawing temperature, causingEato increase. In addition, PVA is a typical polar polymer, so the molecular chains would gradually get close to each other to make more chances for self-hydrogen bonds to rebuilt while increasing the draw ratio.Eawould increase with the increase of draw ratio because hydrogen bonds are sensitive to temperature. The change tendency ofEawith temperature indicated three different activation mechanisms and the fiber could be drawn at least by three steps.

2.2 Drawing behavior of melt-spun PVA fibers with 5% water by mass fraction

According to the comparison between Fig.1 and Fig.4, it can be found that the plasticization effect of water on PVA fibers was weakened, the self-hydrogen bonds of PVA were partly rebuilt, the motion ability of PVA chains was decreased and the tensile stress was increased when the water content decreased. In addition, the drawing behavior of PVA fibers changed and the yield phenomenon was clearly observed in the stress-strain curves of PVA fibers with 5% water by mass fraction. As compared with that of the melt-spun PVA fiber with 35% water by mass fraction, the draw ratio of the melt-spun PVA fibers with 5% water by mass fraction was lower in the drawing temperature below 100 ℃, but higher in the drawing temperature above 140 ℃.

Fig.4 Stress-strain curves of melt-spun PVA fibers with 5% water by mass fraction drawn at different temperature 1—30 ℃；2—60 ℃；3—80 ℃；4—100 ℃；5—110 ℃；6—120 ℃；7—130 ℃；8—140 ℃；9—180 ℃；10—190 ℃；11—200 ℃；12—210 ℃

The main reason is that the motion ability of PVA molecular chains was mainly affected by water at lower temperature below 100 ℃, therefore, the higher water content in PVA fibers, the greater damage to PVA self-hydrogen bond, the more singnificant plasticization effect, the better drawability of PVA fibers, and the higher draw ratio of PVA fibers. What′s more, water evaporated constantly with the increase of temperature, making the fibers generate bubbles and defects and fracture finally. But the melt-spun PVA fiber with lower water content was effectively constrained by water, making water hardly evaporate. So it had few defects resulting from water evaporation, better high-temperature drawablity and higher draw ratio as well, as compared with the fiber with 35% water by mass fraction.

The effect of water on self-hydrogen bonds of PVA was weakened, the self-hydrogen bonds were partly rebuilt and the structure of PVA fiber became denser as the water content in melt-spun PVA fibers was decreased. So the motion ability of PVA molecular chains was depressed andηεwas increased. The change tendency ofηεwith the draw ratio and temperature was similar to that of fiber with 35% water by mass fraction.

The experimental data of lnηεagainst 1/Twere showed in Fig.5, which exhibited two-segment straight line with inflection point temperature being about 200 ℃ which was higher than that of fiber with 35% water by mass fraction.

Fig.5 Relationship between ηε and 1/T of melt-spun PVA fibers with 5% water by mass fraction at different λ■—4；●—5；▲—6；▼—7；◆—8；?—9；?—10；○—11

As shown in Tab.2,the correspondingEaof PVA fibers with 5% water by mass fraction showed two regions,i.e.24.6-33.2 kJ/mol at 30-200 ℃,higher than that of PVA fiber with 35% water by mass fraction in the lower temperature and middle temperature regions,and 111.3-140.6 kJ/mol at 200-220 ℃,also higher than that of PVA fiber with 35% water by mass fraction in higher temperature region. Therefore, there existed two different activation mechanisms,so at least two steps should be adopted during drawing process.The increase ofEaand the change of activation mechanisms of melt-spun PVA fiber with 5% water by mass fraction was due to self-hydrogen bonds rebuilding and dense structure of PVA fibers caused by the decrease of water content.

Tab.2 Ea of melt-spun PVA fibers with 5% water by mass fraction drawn in different temperature regions

3 Conclusions

a. The effect of temperature onηεof melt-spun PVA fiber with 35% water by mass fraction can be divided into three regions, lower-temperature region of 30-100 ℃, middle-temperature region of 100-190 ℃ and higher-temperature region of 190-210 ℃, which indicated that there were three different activation mechanisms and the fiber could be drawn at least with three steps.

b. When the water content of melt-spun PVA fibers was 5% by mass fraction, water could hardly evaporate during hot drawing, the self-hydrogen bonds of PVA were partly rebuilt, the structure of PVA became dense, the motion ability of PVA molecular chains decreased andηεincreased in two regions, i.e. lower-temperature region of 30-200 ℃ and higher-temperature region of 200-220 ℃. The activation mechanisms were different in these two regions.

c. The lower water content was beneficial to the oriented stretch of PVA molecules and stabilization of oriented structure. The water content of the system should be rationally decreased during drawing process to acquire the better stretchability at high temperatures and more outstanding mechanical properties of the melt-spun fibers.

[1] Zhao Huan. Poly(vinyl alcohol) fibers[M]. Beijing: Chemical Industry Press, 2014:7-8.

[2] Bai Hongjun, Yang Zhongkai, Tang Chuanjiang, et al. Rheological behavior of plasticized poly(vinyl alcohol) melt[J]. Chin Syn Fiber Ind, 2015,38(2):43-47.

[3] Lin C A, Ku T. Shear and elongational flow properties of thermoplastic polyvinyl alcohol melts with different plasticizer contents and degrees of polymerization[J]. J Mater Proc Tech, 2008, 200: 331-338.

[4] Hiroshi N, Nobuo D, Takeaki M. Preparation and thermal properties of thermoplastic poly(vinyl alcohol) complexes with boronic acids[J]. J Polym Sci, Part A: Polym Chem, 1998,36(17):3045-3050.

[5] Ku T H, Lin C A. Elongational flow properties of thermoplastic polyvinyl alcohol/polypropylene from the melt spinning method[J]. Text Res J, 2014,84(9):932-940.

[6] Wang Qi, Li Li, Chen Ning. Thermal processing of poly(Vinyl alcohol) [J]. Polym Mater Sci Eng, 2014,30(2):192-197.

[7] Wang Ning, Zhao Lipeng, Zhang Chuhong,et al. Water states and thermal processability of boric acid modified poly (vinyl alcohol) [J]. J Appl Polym Sci,2016,133(13):43246-43252.

[8] Pan Lijun, Hu Zuming, Liu Zhaofeng. A study of elongational rheological behavior of UHME-PE gel fiber[J]. J Chin Text Univ, 1993,19(6): 67-72.

[9] Smook J, Pennings A. The effect of temperature and deformation rate on the hot-drawing behavior of porous high-molecular-weight polyethylene fibers[J]. J Appl Polym Sci, 1982, 27(6): 2209-2228.

?國內外動態?

80 kt/a 高性能再生聚酯纖維項目落戶宜賓

2017年7月12日，由浙江億興達紡織有限公司、紹興新綸機械制造有限公司、佛山中泰光進出口公司共同出資建設的80 kt/a 高性能再生聚酯纖維及紡紗織布產業化項目正式落戶宜賓屏山縣工業園區。據了解，該項目總投資5.2億元，用地約100畝，分二期建設，其中，一期項目選址石盤產業園區，用地約45畝，預計總投資2億元;二期項目擬選址王場產業園區，用地約55畝，預計總投資3.2億元。該項目全部建成并投產后將形成 80 kt/a 高性能再生聚酯纖維及紡紗織布生產能力，實現年產值10億元、利稅1.5億元，新增就業300人以上。目前，該項目正在開展廠房設計等前期工作。

(通訊員 楊 朝)

圣泉集團首創石墨烯功能纖維

2017年6月3日，濟南圣泉集團股份有限公司“生物質石墨烯宏量制備及石墨烯在功能纖維中的產業化應用”成果鑒定發布，該項目是中國紡織工業聯合會科技指導性項目,由圣泉集團承擔，并由工信部、中國化學纖維工業聯合會、中國石化聯合會共同鑒定完成。

由中國工程院院士孫晉良等權威專家組成的鑒定委員會一致認為：該成果發明了天然生物質纖維素制備生物質石墨烯的“基團配位組裝析碳法”，在國際上首次實現了生物質石墨烯材料的宏量制備;研發出具有遠紅外、抗菌抑菌、抗靜電、防紫外等多功能的石墨烯改性纖維，開發其在服飾、家紡、軍工、輕工、醫療、精細化工等領域的應用；該成果對提高紡織工業科技創新能力、紡織行業技術升級和高附加值產品開發具有深遠意義;在國際上首次實現了生物質石墨烯宏量制備及石墨烯在功能纖維中的產業化應用，達到了國際領先水平，屬國際首創。

圣泉集團此次成功突破生物質石墨烯宏量制備及石墨烯在功能纖維中的產業化應用，開發了具有低溫遠紅外、防紫外線、改善微循環、抗菌抑菌、抗靜電、增溫保溫等功能性紡織品，高性能化、多功能化、智能化的紡織纖維材料體系初現。此外，圣泉集團正研發和儲備石墨烯在軍民融合領域、醫療用品、防腐涂料、電池材料、增強材料等領域的技術。

(通訊員 錢伯章)

齊魯石化制成石墨烯腈綸

2017年7月，齊魯石化腈綸廠與山東濟南圣泉集團合作，成功完成石墨烯腈綸試樣的制備工作。經國家紡織制品質量監督檢驗中心對使用該原料制作成織物的試樣進行檢測，產品的抗靜電性、抗菌抑菌性、遠紅外性能及耐水洗色牢度等指標全部達到并超過國家標準。該廠與濟南圣泉集團協商，確定了放大實驗設備的技術需求和具體參數，開始了石墨烯實驗設備采購程序。該項目是提升腈綸產品附加值的有效途徑。

(通訊員 鄭寧來)

上海石化原液著色腈綸銷量增長

2017年1～6月，上海石化腈綸部原液著色腈綸的銷量同比增長49%。原液著色腈綸是該部自行開發的新產品，填補了國內空白，豐富了國內腈綸的品種，使腈綸生產技術水平得到了提升，逐步為國內客戶所接受。該部原液著色腈綸銷售量的擴大，得益于品種的增加。2015年，該部還只能生產單一的黑色纖維，而現在，已有十多種顏色的腈綸進入正常生產序列，另外還有二十多種顏色的腈綸產品進入技術儲備序列。顏色增多，客戶選擇的余地也大了。另外，該部生產的原液著色腈綸原來僅用來做戶外產品，現在則已進入了服用領域。

(通訊員 錢伯章)

聚乙烯醇熔紡初生纖維的拉伸行為研究

李莉 陳寧 劉慶

(1.四川大學 高分子材料工程國家重點實驗室，高分子研究所，四川 成都 610065)

采用去離子水溶脹聚乙烯醇(PVA)，通過熔融紡絲法制備PVA纖維。研究了水質量分?jǐn)?shù)35%和5%的PVA熔紡初生纖維在不同拉伸溫度下的應力-應變曲線，以及其拉伸活化機制。結果表明：拉伸溫度對水質量分?jǐn)?shù)35%的PVA熔紡初生纖維表觀拉伸黏度的影響分為3個區，即30～100 ℃，100～190 ℃，190～210 ℃，纖維在熱拉伸時存在3個不同機制的活化過程，至少可采用三級拉伸；初生纖維拉伸受體系中水含量的影響，水含量減少，PVA分子鏈運動能力降低，表觀拉伸黏度增大，水質量分?jǐn)?shù)5%的PVA熔紡初生纖維的表觀拉伸黏度隨溫度變化呈現兩個區，活化機制改變，可采用兩步拉伸。

聚乙烯醇纖維 熔融紡絲 拉伸黏度 活化能

date:04-05-2017; revised date: 20- 06- 2017.

National Natural Science Foundation of China(51433006) and Independent Project of State Key Laboratory of Polymer Materials Engineering of China(sklpme2014-3-15)

TQ342+.41 Document code:A Article ID: 1001- 0041(2017)04- 0040- 05

Biography: Li Li(1977-), female,Ph. D,is engaged in the structure and properties of polymers. E-mail：powerlily@scu.edu.cn.

* Corresponding author: ningchen@scu.edu.cn.